Toyota Landcruiser 70 Series Bullbars: Installation Tips for NZ Owners

Most Toyota Landcruiser 70 Series owners in NZ buy the ute first and worry about the Bullbars later. That's normal — but it's also where the trouble usually starts. By the time you're planning your first proper trip out to Hawkes Bay backcountry, the Bullbars on a stock or budget-fitted Toyota Landcruiser 70 Series starts to show its limits.

If you ever want to see the gap between a well-kept Toyota Landcruiser 70 Series and a tired one, look at the Bullbars. Everything else can be polished and detailed; this is the system that tells the truth about how the ute has actually been used and looked after.

What follows is the practical version of what every Toyota Landcruiser 70 Series owner eventually learns the hard way. Think of it as the conversation you'd have with a mate who's been there — the one who'd point at three things, save you a few grand, and then crack open another beer.

Why bullbars matters on the Toyota Landcruiser 70 Series

The Toyota Landcruiser 70 Series is a workhorse, which means the Bullbars is doing more than most drivers realise. Every kilometre, every load, every off-camber corner is feeding stress into the system.

Anyone who's stripped a Toyota Landcruiser 70 Series down knows the Bullbars is one of the most over-engineered AND under-engineered parts of the platform — over-engineered where it doesn't matter, under-engineered where it does. Owners who upgrade get capability the OEM never intended; owners who don't get failures the OEM didn't predict.

On the legal side, the LVVTA system in NZ catches more Bullbars modifications than people expect. WoF inspectors are increasingly switched-on to aftermarket changes, and an undocumented mod can pull the WoF off an otherwise sorted ute. Plan for cert from day one.

What to look for in bullbars for the Toyota Landcruiser 70 Series

If you're comparing two products, here's the comparison framework that separates the winners from the regrets:

• Material and coating quality — In NZ, the difference between marine-grade powder coat and zinc plating is two years of life or ten. Anywhere coastal — Northland, East Cape, the West Coast — needs the upgrade.
• LVVTA / WoF signalling — Reputable suppliers state cert requirements explicitly. If a supplier hedges or hand-waves, that's a signal worth paying attention to.
• Documentation — Installation specs, torque values, and re-check intervals should come with the part. If they don't, you're buying half a product.
• Generation-specific fitment — Don't trust generic 'Toyota Landcruiser 70 Series' listings. Year ranges and chassis codes matter. A part listed for one generation will rarely cross-fit cleanly to another.
• Country of origin and supply chain — Local NZ stock and warranty support matter when something goes wrong. International orders are cheaper until you need a replacement under warranty.

Most owners who learn the Bullbars lesson learn it the expensive way: cheap part fails, secondary component dies in sympathy, the proper version gets bought anyway, and the original 'savings' are long gone. Skip that loop.

NZ use-case: Hawkes Bay backcountry

If you've never driven Hawkes Bay backcountry, it's worth knowing what it does to a 4x4. The mix of surfaces, gradients, and exposure makes it a benchmark of sorts — a track that finds the weakest part of any setup.

The other thing about Hawkes Bay backcountry is that the conditions vary so quickly. You might be on dry gravel one minute and a wet clay corner the next. That kind of variation is brutal on Bullbars components, especially the seals and bushes that don't like rapid temperature change.

Kren Bits picks for your Toyota Landcruiser 70 Series

Below are honest product recommendations for Toyota Landcruiser 70 Series owners shopping the Bullbars category right now. These are the ones we'd put on our own ute:

• '75-84 Toyota Land Cruiser FJ40 FJ43 FJ45 HJ45 HJ47 Exterior Door Handle (75-84) — Honest fitment, sensible price point, and a known-good supplier — the kind of part we'd fit to our own ute.
• 1974-1980 Toyota Land Cruiser FJ40 FJ45 BJ40 Rear Reflector Lamp (1974-1980) — If you're upgrading from worn factory parts, this lands squarely in the sweet spot of value and longevity.
• FZJ78 FZJ79 HDJ78 HDJ79 HZJ78 HZJ79 Leading Radius Arm Chassis Bush Kit — A reliable middle-ground option that suits owners who want OEM-plus rather than full aftermarket commitment.

Whichever option you pick, the rule for the Toyota Landcruiser 70 Series is the same: install it once and then maintain it forever. Nothing in this category is a true 'fit and forget' part.

Installation notes

• Threadlocker on the right fasteners — Medium-strength on anything that vibrates and isn't routinely serviced. Skip the high-strength stuff unless the spec sheet calls for it — you'll wreck threads getting it apart later.
• Torque to spec, then re-check at 500km — New components settle. Bolts that felt right on the hoist are often a quarter-turn loose after the first proper drive. Don't skip this step.
• Wheel alignment after any geometry change — Even minor Bullbars changes can affect tracking. An alignment is far cheaper than a set of front tyres eaten in 5,000 km.
• Sensor and brake-line clearance — Modern Toyota Landcruiser 70 Series models have ABS sensors, ride-height sensors, and brake lines routed in places that change with even minor mods. Always verify clearance after installation.
• Document the install — Take photos, save invoices, save spec sheets. If the ute ever gets sold or needs a re-cert, this paperwork is gold.

Long-term maintenance

1. Every 10,000 km — torque check on all serviceable Bullbars fasteners. Use a torque wrench, not a feel-test. Document any bolt that needed re-tensioning.
2. Annually — full system review with measured ride heights, alignment, and a written record. A 10mm sag on one side over twelve months is a sign that a component is failing.
3. Every 20,000 km — wear part assessment. Bushes, mounts, and consumables all have a real-world lifespan in NZ conditions. Replace as a set, not one-by-one.
4. Every 5,000 km — visual inspection. Walk around the ute. Look for fluid weep, cracked bushes, sagging components, missing bolts. Ten minutes saves thousands.

Anyone who's stripped a Toyota Landcruiser 70 Series down knows the Bullbars is one of the most over-engineered AND under-engineered parts of the platform — over-engineered where it doesn't matter, under-engineered where it does. Owners who upgrade get capability the OEM never intended; owners who don't get failures the OEM didn't predict. The other thing about Hawkes Bay backcountry is that the conditions vary so quickly. You might be on dry gravel one minute and a wet clay corner the next. That kind of variation is brutal on Bullbars components, especially the seals and bushes that don't like rapid temperature change.

Summing up

Look after the Bullbars on your Toyota Landcruiser 70 Series and the rest of the ute looks after itself. It really is that simple. Twenty minutes every five thousand kilometres, an annual full review, and a refusal to defer the obvious — that's the entire programme.

When in doubt, ask. Drop us your rego on the Kren Bits contact page and we'll match the right Bullbars parts to your specific Toyota Landcruiser 70 Series build. No pressure, no upsell — just real recommendations from people who run the same utes.